4th of July Over the Top Bow, “Star Spangled Cutie”

4th of July Over the Top Bow with “Star Spangled Cutie” removable/changeable bottle cap

Date Created: 7/2016
Difficulty Level: Advanced
Time to Complete: 30+ minutes
Pricing: $7.00
IMG_20170310_154815
Materials Needed:
  • 3/8″ ribbon
    • red with white dots
    • navy& white lollipop stripes
  • 7/8″ ribbon
    • turquoise
    • white
    • navy
    • red & white stripe
  • 50-60cm french clip
  • 1.75″ alligator clip
  • 1″ bottle cap image
  • 1″ epoxy dot
  • 1″ bottle cap
  • E6000 glue
  • scissors
  • needle and thread
  • hot glue gun
  • lighter or heat seal source
Measurements: (and what the pieces are for)
  • 16″ of 7/8″ turquoise for boutique bow
  • 5″ of 3/8″ red with white dots for center
  • 4.5″ of 3/8″ red with white dots for clip liner
  • 6″ of 3/8″ red with white dots for center wrap
  • (2) 9″ of 3/8″ red with white dots for top bow surround
  • (2) 9.5″ of 3/8″ white & navy lollipop stripes for bottom bow surround
  • Spikes (all 4″, but I think 4.5″ would have worked better on this bow)
    • (2) 7/8″ turquoise
    • (2) 7/8″ white
    • (2) 7/8″ navy
    • (1) 7/8″ red & white stripe
Note:
After making boutique bow, it measured 3″ from corner to corner. So to measure the spikes I added 1″ and cut them at 4″.  However, these spikes ended up a bit too short and didn’t stick out under the bow at all.  I would try measuring spikes to be 1.5″ longer than longest length of the boutique bow.
Instructions:
Sorry, no tutorial available yet for this one.  Please add a comment below if you’d like to request to see instructions on how to make this bow.
Advertisements

Pinwheel (5/8″ ribbon) Hair Bow for 4th of July

Date Created: 6/2016
Difficulty Level: Beginner
Time to Complete:
Pricing: $2.50
66b9b546-8a82-4af5-b35b-1ea5a220c4ec.jpg
Materials Needed:
  • 5/8″ grosgrain ribbon (blue with white stars)
  • 5/8″ grosgrain ribbon (red)
  • 3/8″ grosgrain ribbon (white)
  • small clip
 
Measurements: (and what the pieces are for)
  • top half of pinwheel: 4″ of 5/8″ grosgrain ribbon (blue with white stars)
  • bottom half of pinwheel: 4″ of 5/8″ grosgrain ribbon (red)
  • center wrap: 4″ of 3/8″ grosgrain ribbon (white)
 
Instructions:
  • Fold ribbon as if making a tuxedo bow, but add both ribbons to the needle and thread.  Cinch the thread, wrap and tie off, to make a pinwheel.

7/8″ Pinwheels with No Tails, Double Bow Tie Style

Date Created: Summer 2016
Difficulty Level: Beginner
Time to Complete: 10-15 minutes
Pricing: $2+ depending on price of ribbon and other materials
Materials Needed:
  • 7/8″ grosgrain ribbon
  • 3/8″ grosgrain ribbon
  • alligator clip or barrette (30-40mm hair clip, I used a 40mm French clip in this example, but I’ve also used 30-40mm flat rectangular top toothed alligator clips as well.)
  • needle and thread
  • hot glue
Measurements:
  • (2) 6″ pieces of 7/8″ grosgrain, for pinwheel
  • (1) 4″ piece of 3/8″ grosgrain, for center wrap
Instructions:

These pinwheels are made with 2 pieces of stitched ribbon using 7/8″ grosgrain, mounted on a 40mm French clip, wrapped with 3/8″ matching grosgrain at the center and measure 2 1/2″ in width at completion.

Fold the 7/8″ ribbons in half and mark the center. Then, 1 ribbon at a time, fold the ribbon like you are going to make a tuxedo bow tie and using the needle and thread, make 2 stitches down the center. Repeat on the 2nd ribbon. Wrap and cinch together neatly. Glue clip on and wrap center.

I’ve made these in every color of 7/8″ ribbon I have, which is about 25 colors.  They are such a popular and cute clip and so easy to make.  They are much quicker to make and cheaper if you mount them on an alligator clip than a french barrette clip, however, nothing stays in my daughter’s hair unless it is on a french clip. I sell these for $2 at the craft fairs and they go quickly.

 

 

Pinwheels with Spikes and Mustache Bottle Cap

Stacked pinwheels with no tails and a layer of spikes with bottle cap with a mustache

IMG_20160610_220557.jpg

Pinwheel, 2 stacked no tail pinwheels on spikes with mustache bottle cap

  • 12″ of 7/8″ RABOM aqua to make pinwheel with no tails on 2 3/4″ template
  • 16″ of 1 1/2″ hot pink to make pinwheel with no tails on 3 1/2″ template
  • (2) 5 1/4″ of 1 1/2″ black for spikes
  • Mounted on french clip

Pinwheel with “Mommy Makes My Bows” Bottle Cap

Stacked no tail pinwheels with spikes and bottle cap

 

  • 12″ of 7/8″ black to make no tails pinwheel on 2 3/4″ template
  • 16″ of 1 1/2″ white to make no tails pinwheel on 3 1/2″ template
  • (2) 5″ of 1 1/2″ shocking pink to make 2 spikes
  • Stack bows
  • 4-5″ of 3/8″ ribbon for center
  • Mounted on french clip
  • Top with bottle cap

Pinwheel with Princess Castle Bottlecap

This is a double layer pinwheel with a bottle cap of a pink and purple princess castle.

  • 11 1/2″ of 7/8″ shocking pink made into no tails pinwheel on 2 1/2″ bow template
  • 16″ of 1 1/2″ light pink made into no tails pinwheel on 3 1/2″ bow template
  • stack bows, mount on medium french clip with 3/8″ shocking pink center wrap
  • embellish with Princess Castle bottle cap

img_20160622_091149