Witch Hat 3D Ribbon Sculpture Hair Clip

Date Created: 10/6/2014
Difficulty Level: Intermediate
Time to Complete: 30 minutes?
Pricing: $5+ depending on materials and embellishments
2014-09-09 Fall Sculptures (26) pm 2
Materials Needed:
  • 2 1/4″ black ribbon
  • 1/4″ black ribbon
  • 3/8″ Halloween ribbon
  • cardboard or plastic to create templates
  • template to trace for hat circle and cone
  • light colored pencil for marking black ribbon
  • needle and black thread
  • 1 3/4″ single prong salon clip aka alligator clip
  • non-slip grip like Silly Grip
  • hot glue gun
  • lighter
  • protective heat mat
 
Measurements: (and what the pieces are for)
  • 2 1/4″ of 2 1/4″ black ribbon for round hat bottom
  • 3″ of 2 1/4″ black ribbon for hat cone
  • 5″ of 3/8″ Halloween ribbon for bow, cut edges into V shape
  • 3/4″ of 1/4″ black ribbon for bow center wrap
  • 3 1/2″ of 3/8″ Halloween ribbon for hat wrap, cut edges at 30% slant up
  • 4 1/2″ of  3/8″ Halloween ribbon for alligator clip liner
 
Instructions:
  • These are very general instructions, so I hope to be posting a video with more detail as soon as I can.
  • Trace templates for circle and cone onto the pieces of 2 1/4″ black ribbon using a white chalk pencil or light colored pencil so you can see where to cut it.
  • Cut out circle and cone, and heat seal all edges.
  • Wrap cone piece into cone shape and glue into place. (I’ll be making a video shortly showing how to do this, it is a little tricky.)
  • Use scissors if necessary to even out bottom of hat so it will sit flat on the circle, just make sure there are no bumps.
  • Starting in the back of the hat on the crease, glue the 3 1/2″ piece of Halloween ribbon to the hat with 1 dot.  It will still be sticking out on both sides.
  • 1 side at a time, add a little glue and adhere, wrapping it around to the front.  It will not all go on, it will slant down, and you will cut off the excess afterwards.
  • Cut off excess from wrap.
  • As evenly and quickly as possible, line glue around the entire circular bottom of hat cone and then center and stick onto hat circle before it dries.
  • Make bow, and glue onto center front of hat where points of hat wrap meet, thus covering that part up.
  • Finally, determine which way your hat will face and glue onto a ribbon lined alligator clip.

Witch Hat Ribbon Sculpture Hair Clip

Date Created: 2014
Difficulty Level: Beginner
Time to Complete: 20 minutes
Pricing: $5 +
spiders-and-hats-039p
Materials Needed:
  • 7/8″ black grosgrain ribbon
  • 3/8″ black grosgrain ribbon
  • 1/8″ black grosgrain ribbon
  • 3/8″ Halloween print grosgrain ribbon

Measurements: (and what the pieces are for)

witch-hat-flat-tutorial

  • Cone: 1 1/4″ of 7/8″ black ribbon
  • Hat belt: 1 3/4″of 3/8″ Halloween ribbon
  • Brim:  2″ of 3/8″ black ribbon
  • Bow wrap: 3/4″ of 1/8″ black ribbon
  • Mini BowTie : 2″ of 3/8″ Halloween ribbon
  • Clip Liner: 4 1/2″ of 3/8″ Halloween ribbon
Quick Instructions:
  • Fold 7/8″ ribbon into cone shape and glue folds in.
  • Glue hat belt onto cone with slight overlap.
  • Round ends of the black brim using lighter, then using slight overlap, glue onto hat belt.
  • Determine which way the hat will face, left or right and make bow tie and glue on.
  • Attach bow to ribbon lined clip.

Video Tutorial (sorry no sound):

Other Halloween ribbon patterns to consider.  Check EBAY for great prices on ribbon.

PicMonkey Collage hats1.jpg

Bat Ribbon Sculpture Hair Clip

Date Created: 2014
Difficulty Level: Advanced
Time to Complete: 45  minutes +
Pricing: $8 +
img_20150925_150001
Materials Needed:
  • 3/8″ black grosgrain ribbon
  • 3/8″ Halloween print grosgrain ribbon
  • 1/8″ black grosgrain ribbon
  • 8mm googly eyes
  • alligator clip

Materials: All measurements are of 3/8″ grosgrain unless otherwise stated

  • Wings: (2) 6″ black ribbon folded with 1 fold at 3/4″, 2 folds at 1″, 1 fold at 1 1/4 inch and last piece at 1 3/4″ connecting to other end
    • Mark ribbon for creases with glue at 3/4″, 1 3/4″, 2 3/4″, 4″
  • Head: (3) 2″ black ribbon
  • Body: (3) 2 1/4″ black ribbon
  • Bow: 2″ of 3/8″ Halloween ribbon
  • Bow Center: 3/4″ of  1/8″ black ribbon
  • Eyes: (2) 7-8mm googly eyes
  • Clip: 4 1/2″ Mount on Halloween ribbon lined alligator clip (choice of left, right or vertical)

Mounting Options: this can also be mounted on a pin to wear or a magnet for the fridge or a badge clip for work.